350 Watt ITE Open Frame FXA350

Home

Elpac by ICCNexergy

Features:

High Efficiency: Level V
Wide Range AC Input
Power Factor Correction
+5 Standby & Fan Power
Fully Regulated DC Output
EISA and CEC Compliant
Grounded Output
ITE and Medical Grade Approval

PEI can modify standard power supplies within 5 business days.

Model Overview

Elpac Part Number	Output Voltage	Output Current¹	Typical Efficiency²
FXA350012A	12.0V	20A	88%
FXA350015A	15.0V	16.5A	88%
FXA350024A	24.0V	10.5A	88%
FXA350028A	28.0V	9.0A	89%
FXA350048A	48.0V	5.3A	88%

Input

Input Voltage

85 - 264VAC 100 - 240VAC Nominal

Input Frequency

47 – 63Hz

Input Current

<5A rms

Inrush Current

<37A at 230VAC cold start

Power Factor

>0.98

Zero Load Power Consumption

<0.75W

Touch Leakage Current

<200µA @ 132VAC @ 60Hz

<300µA @ 264VAC @ 60Hz

Output

Output Voltage

See Table

Total Regulation

+/-5%

Minimum Load

No minimum load required

Start-Up Delay

<1s

Hold-Up Time

>24ms at any Input Voltage

Ripple & Noise

<1% pk-pk ** *

Over Voltage Protection

110-135%

Over Temperature Protection

Active - Recoverable; plus Passive - Non Recoverable

Over Current Protection

120 - 180%

Short Circuit Protection

Shutdown, auto-restart (hiccup mode)

General

Efficiency

Avg Efficiency 88.5% @ 115VAC; 90.6% @ 230VAC

MTBF

min. 200,000 hours demonstrated

Size

8.00" x 5.00" x 1.50" | 203.2mm x 127mm x 38.1mm

Weight

2.1 lbs (0.95 kg)

Environmental

Operating Temperature

0 – 70°C (Full load to 50°C, derate linearly to 50% load at 70°C)

Storage Temperature

-40°C to +85°C

Relative Humidity

5-95%, non-condensing

Cooling

Natural Convection (250W) or Forced Air (350W)

Vibration

All units production tested to 19.6m/s²

EMC & Safety

Emissions

FCC class B, CISPR22 class B EN61000-3-2, -3

Immunity

EN61000-4-2, -3, -4, -5, -6, -8, -11

Certified by TUV to the following:

cTUVus

UL 60950-1

CAN/CSA-22.2 No.60950-1

CB per IEC60950-1

CE marked to LVD

Notes

1 With convection cooling. Peak load (350W) lasting 500ms with a maximum 10% duty cycle.
2 Typical at 115VAC and full load.

* Ripple and noise measured with 20MHz bandwidth; 10μF tantalum capacitor in parallel with a 0.1μF ceramic capacitor.

Input / Output Configuration

Input Configuration (H1)

Connection on Power Supply Body

JITE p/n BTB555-10-03 Barrier Strip, M3 screws

Pin 1

AC Line

Pin 2

AC Neutral

Pin 3

Ground

Output Configuration (H4)

Connector (PSU side)

JITE p/n BTB555-10-04 Barrier Strip, M3 screws

Pin 1

+V1

Pin 2

+V1

Pin 3

Return

Pin 4

Return

Signal Configuration (H2)

Connector

AMP P/N 640456-8 or equivalent

Mating Connector

AMP p/n 640440-8 or equivalent

Pin 1

DC-Good / TTL high when DC is within regulation

Pin 2

AC Fail / TTL high when AC is present;
min. 8ms warning before loss of DC output

Pin 3

Remote On/Off / Connect to Pin 7 (Rtn) to enable power supply

Pin 4

+ Sense / Must be connected to output, either at H4 connector,
or at point of load. Will compensate for up to 500mV cable drop.

Pin 5

- Sense / Must be connected to output, either at H4 connector,
or at point of load. Will compensate for up to 500mV cable drop.

Pin 6

No Connection

Pin 7

Return for Remote on/off and +5V Standby

Pin 8

Return to Pin 7 for +5V @ 1.0A Standby output

Fan Configuration (H3)

Connector

AMP P/N 640456-8 or equivalent

Mating Connector

AMP p/n 640440-8 or equivalent

Pin 1

+V / Fan output will adjust from +5V to +12V depending on ambient temperature.

Pin 2

+V / Fan output will adjust from +5V to +12V depending on ambient temperature.

350 Watt ITE Open Frame FXA350

Model Overview

Input / Output Configuration

Mechanical Drawing

Certifications